View B133EW03-V0_7871358.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

au optronics corporation b133ew03 v0 product specification document version 0.1 1 v preliminary specifications final specifications module 13.3? wxga color tft-lcd model name b133ew03 v0 customer date checked & approved by note: this specification is subject to change witho ut notice. approved by date prepared by nbbu marketing division / au optronics corporation www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 2 contents record of revision 1. handling precautions ............................ ................................................... ............................... 4 2. general description............................. ................................................... ................................. 5 2.1 general specification .......................... ................................................... .............................................5 2.2 optical characteristics ........................ ................................................... .............................................6 3. functional block diagram ........................ ................................................... ......................... 11 4. absolute maximum ratings........................ ................................................... ....................... 12 4.1 absolute ratings of tft lcd module............. ................................................... .............................12 4.2 absolute ratings of backlight unit............. ................................................... ...................................12 4.3 absolute ratings of environment ................ ................................................... ..................................12 5. electrical characteristics ...................... ................................................... ............................. 13 5.1 tft lcd module................................. ................................................... ..........................................13 5.2 backlight unit ................................. ................................................... ...............................................15 6. signal characteristic ........................... ................................................... ............................... 16 6.1 pixel format image ............................. ................................................... ...........................................16 6.2 the input data format .......................... ................................................... ...........................................17 6.3 signal description/pin assignment.............. ................................................... ..................................18 6.4 interface timing ............................... ................................................... ..............................................20 7. connector description ........................... ................................................... ............................ 22 7.1 tft lcd module................................. ................................................... ..........................................22 8. vibration and shock test........................ ................................................... ........................... 23 8.1 vibration test ................................. ................................................... ................................................23 8.2 shock test spec:............................... ................................................... ..............................................23 9. reliability..................................... ................................................... ........................................ 24 10. mechanical characteristics ..................... ................................................... ........................ 25 10.1 lcm outline dimension......................... ................................................... .....................................25 11. shipping and package ........................... ................................................... .......................... 27 11.1 shipping label format ......................... ................................................... ........................................27 11.2. carton package ............................... ................................................... .............................................28 11.3 shipping package of palletizing ............... ................................................... ....................................29 www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 3 version and date page old description new description remark 0.1 2007/06/25 all first edition for customer www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 4 1. handling precautions 1) since front polarizer is easily damaged, pay att ention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact wi th water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with a bsorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break o r crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) at the insertion or removal of the signal interf ace connector, be sure not to rotate nor tilt the interface connector of the tft module. 10) after installation of the tft module into an en closure notebook pc bezel, for example , do not twist nor bend the tft module even momenta ry. at designing the enclosure, it should be taken into consideration th at no bending/twisting forces are applied to the tft module from outside. otherwise the tft module may be damaged. 11) small amount of materials having no flammabilit y grade is used in the lcd module. the lcd module should be supplied by power complied with requirements of limited power source , iec60950 or ul1950 , or be applied exemption. www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 5 2. general description b133ew03 v0 is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and backlight system. the screen format is intended to support the wxga 1280 h x 800 v screen and 262k colors rgb 6-bits data driver . all input signals are lvds interface compatible. inverter of backligh t is not included. b133ew03 v0 is designed for a display unit of noteb ook style personal computer and industrial machine. 2.1 general specification the following items are characteristics summary on the table at 25 condition: items unit specifications screen diagonal [mm] 3 3 7. 8 1 3.3 w? active area [mm] 286.08 h x 178.8 v pixels h x v 1280x3 rgb x 800 pixel pitch [mm] 0.2235 x 0.2235 pixel arrangement r.g.b. vertical stripe display mode normally white white luminance iled=16.0ma [cd/m 2 ] 330typ. 5 points average 270 min. 5 points average luminance uniformity 1.8 max. 5 points contrast ratio 500:1 typ.,300:1 min. backlight mode led ( x54 ) optical rise time/fall time [msec] 16 typ., 25 max. nominal input voltage vdd [volt] +3.3 typ. power consumption [watt] logic 0.7w; blu 3.5w(max) weight [grams] 210 g typ., 225g max. physical size [mm] 297.15 (w) x 203.15 (h) x 2.7 ( t) typ. electrical interface r/g/b data, 3 sync, signals, clock 4 pairs lvds surface treatment hard coating 3h, glare type, support color 262k colors rgb 6-bit temperature range operating storage non-operating [ o c] [ o c] 0 to +50 -20 to +60 rohs compliance rohs compliance www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 6 2.2 optical characteristics the optical characteristics are measured under stab le conditions at 25 room temperature : item unit conditions min. typ. max. note white luminance i f =20ma [cd/m 2 ] 5 points average 270 330 - 1, 4, 5. [degree] [degree] horizontal right cr = 10 (left 60 60 75 75 - - viewing angle (6 o?clock direction) [degree] [degree] vertical upper cr = 10 lower 55 50 65 60 - - 9 luminance uniformity 5 points 1.25 1 luminance uniformity 13 points 1.80 2 cr: contrast ratio 300 500 - 6 cross talk % 1.4 7 [msec] rising - 5 10 [msec] falling - 11 15 response time [msec] rising + falling 16 25 8 white x 0.283 0.313 0.343 color/chromaticity-- panel coordinates ( cie 1391 ) white y 0.299 0.329 0.359 rx 0.570 0.600 0.630 ry 0.315 0.345 0.375 gx 0.290 0.320 0.350 gy 0.525 0.555 0.580 bx 0.120 0.150 0.180 color / chromaticity-- led coordinates ( cie 1391 ) by 0.090 0.120 0.150 www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 7 1 2 3 4 5 h / 4 h / 4 h / 4 h / 4 h w w / 4 w / 4 w /4 w / 4 note 2: 13 points position w /4 w w /4 h h /4 h /4 h /4 h /4 7 9 1 0 w /4 1 8 w /4 1 0 1 0 1 0 1 0 2 3 1 3 1 2 4 5 6 1 1 note 3: the luminance uniformity of 5 and 13 point s is defined by dividing the maximum luminance valu es by the minimum test point luminance w13 = maximum brightness of thirteen points minimum brightness of thirteen points maximum bright ness of five points w5 = minimum brightness of five points www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 8 note 4: measurement method the lcd module should be stabilized at given temper ature for 30 minutes to avoid abrupt temperature ch ange during measuring. in order to stabilize the luminan ce, the measurement should be executed after lighti ng backlight for 30 minutes in a stable, windless and dark room. note 5 definition of average luminance of white y l : measure the luminance of gray level 63 at 5 points y l = [l 1 + l 2 + l 3 + l 4 + l 5 ] / 5 l x is corresponding to the luminance of the point x a t figure in note 1 . note 6 definition of contrast ratio: contrast ratio is calculated with the following for mula. center of the screen tft - lcd module 50 cm photo detector ( sr3 or equivalent ) lcd panel field=2 contrast ratio (cr)= brightness on the ?white? state brightness on the ?black? state www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 9 note 7 definition of cross talk ct ct = | y b ? y a | / y a 100 % where y a = luminance of measured location without gray level 0 pattern cd/m 2 y b = luminance of measured location with gray level 0 pattern cd/m 2 note 8: definition of response time: the output signals of bm-7 or equivalent are measur ed when the input signals are changed from ?black? to ?white? falling time and from ?white? to ?black? rising time , respectively. the response time interval between the 10% and 90% of amplitudes. refer to fig ure as below. "black" tr tf "white" "white" 0 % 10 % 90 % 100 % optical response www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 10 note 9. definition of viewing angle viewing angle is the measurement of contrast ratio R 10, at the screen center, over a 180 horizontal an d 180 vertical range off-normal viewing angles . the 180 viewing angle range is broken down as fo llows; 90 ? horizontal left and right and 90 ? vertical, high up and low down . the measurement direction is typically perpendicular to the display surface with the screen rotated about its center t o develop the desired measurement viewing angle. www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 11 3. functional block diagram the following diagram shows the functional block of the 13.3 inches wide color tft/lcd module: www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 12 4. absolute maximum ratings absolute maximum ratings of the module are as follo wing: 4.1 absolute rating of tft lcd module item symbol min max unit conditions logic/lcd drive voltage vdd -0.3 +4.0 [volt] note 1,2 4.2 absolute rating of backlight unit item symbol min max unit conditions led current iled - 30 [ma] note 1,2 4.3 absolute ratings of environment item symbol min max unit conditions operating temperature top 0 +50 [ o c] note 3 operation humidity hop 5 95 [%rh] note 3 storage temperature tst -20 +65 [ o c] note 3 storage humidity hst 5 95 [%rh] note 3 note 1: at ta 25 note 2: permanent damage to the device may occur if exceed maximum values note 3: for quality performance, please refer to au o iis incoming inspection standard . twb=39c operating range storage range www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 13 5. electrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows; symble parameter min typ max units note vdd logic/lcd drive voltage 3.0 3.3 3.6 [volt] pdd vdd power 0.7 1.0 [watt] note 1 idd idd current 270 330 [ma] note 1 i rush inrush current 0.81 1.5 [a] note 2 vddrp allowable logic/lcd drive ripple voltage 100 [mv] p-p note 1 : maximum measurement condition mosaic note 2 measure condition q3 ao6402 g d2 s d1 d5 d6 c3 0.01uf/25v c2 1uf/25v c1 1uf/16v q3 ao6402 g d2 s d1 d5 d6 f1 vr1 47k +12.0v vcc sw1 sw mag-spst 1 2 (lcd module input) (high to low) control signal r2 1k r2 1k r1 47k +3.3v 90% 10% vin rising time 0v 3.3v 0.5ms www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 14 5.1.2 signal electrical characteristics input signals shall be low or high-impedance state when vdd is off. signal electrical characteristics are as follows; parameter condition min max unit vth differential input high threshold vcm=+1.2v 100 [mv] vtl differential input low threshold vcm=+1.2v -100 [mv] vcm differential input common mode voltage 0.8 2.0 [v] note: lvds differential voltage www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 15 5.2 backlight unit parameter guideline for led parameter min typ max units condition white luminance 5 points average 270 330 - [cd/m 2 ] ta=25 led current iled - 16 - [ma] ta=25 note 2 led power consumption - 3.3 [watt] ta=25 note 6 www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 16 6. signal characteristic 6.1 pixel format image following figure shows the relationship of the inpu t signals and lcd pixel format. r g b r g b r g b r g b r g b r g b r g b r g b 0 1 1278 1279 1st line 800th line www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 17 6.2 the input data format signal name description +r5 +r4 +r3 +r2 +r1 +r0 red data 5 msb red data 4 red data 3 red data 2 red data 1 red data 0 lsb red-pixel data red-pixel data each red pixel's brightness data consists of these 6 bits pixel data. +g5 +g4 +g3 +g2 +g1 +g0 green data 5 msb green data 4 green data 3 green data 2 green data 1 green data 0 lsb green-pixel data green-pixel data each green pixel's brightness data consists of these 6 bits pixel data. +b5 +b4 +b3 +b2 +b1 +b0 blue data 5 msb blue data 4 blue data 3 blue data 2 blue data 1 blue data 0 lsb blue-pixel data blue-pixel data each blue pixel's brightness data consists of these 6 bits pixel data. rxclkin data clock the signal is used to strobe the pixel data and de signals. all pixel data shall be valid at the falling edge when the de signal is high. de display timing this signal is strobed at the fal ling edge of rxclkin. when the signal is high, the pixel data shall be valid to be displayed. vs vertical sync the signal is synchronized to rxcl kin . hs horizontal sync the signal is synchronized to rx clkin . note:output signals from any system shall be low or high-impedance state when vdd is off. www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 18 6.3 signal description/pin assignment tbd www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 19 note2: input signals shall be low or high-impedance state when vdd is off. internal circuit of lvds inputs are as following. the module uses a 100ohm resistor between positive and negative data lines of each receiver input www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 20 6.4 interface timing 6.4.1 timing characteristics basically, interface timings should match the 1280x 800 /60hz manufacturing guide line timing. parameter symbol min. typ. max. unit frame rate - 60 - hz clock frequency 1/ t clock 71.1 mhz period t v 803 823 1023 active t vd 800 800 800 vertical section blanking t vb 3 23 223 t line period t h 1303 1440 2047 active t hd 1280 1280 1280 horizontal section blanking t hb 23 160 767 t clock ss: 1.5% note : de mode only 6.4.2 timing diagram dotclk de t h t hb t hd de t v t vb t vd input timing definition ( de mode) t clock input data pixel 1 pixel 2 pixel 3 pixel n-1 pixel n invaild data invaild data pixel 1 www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 21 6.5 power on/off sequence vdd power and lamp on/off sequence is as follows. i nterface signals are also shown in the chart. signals from any system shall be hi-z state or low level when vdd is off. power sequence timing value parameter min. typ. max. units t1 0.5 - 10 ms t2 0 - 50 ms t3 0 - 50 ms t4 400 - - ms t5 200 - - ms t6 200 - - ms t7 0 - 10 ms t4 t3 t2 t5 valid data t1 10% 90% 10% 90% t6 t 7 power supply vdd lvds interface backlight on www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 22 7. connector description physical interface is described as for the connecto r on module. these connectors are capable of accommodating the f ollowing signals and will be following components. 7.1 tft lcd module connector name / designation for signal connector manufacturer ipex type / part number 20347-330e-12 mating connect/part number 20345-xx-xx www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 23 8. vibration and shock test 8.1 vibration test test spec: test method: non-operation acceleration: tbd frequency: tbd sweep: tbd 8.2 shock test spec: test spec: test method: non-operation acceleration: tbd active time: tbd pulse: tbd www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 24 9. reliability items required condition note temperature humidity bias 40 /90%,48hr high temperature operation 50 /20%,48hr low temperature operation 0 ,300hr on/off test 25 , on/10 sec. off/10sec., 30,000 cycles hot storage 60 /20% rh ,48 hours cold storage -20 /50% rh ,48 hours thermal shock test -20 /2hr ,60 /2hr 12cycles shock test non-operating tbd vibration test non-operating tbd esd tbd note 1 note1: according to en61000-4-2 , esd class b: some performance degradation allowed. no data lost . self-recoverable. no hardware failures. note3: mtbf excluding the led : 30,000 hours with a confidence level 90% www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 25 10. mechanical characteristics 10.1 lcm outline dimension www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 26 www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 27 11. shipping and package 11.1 shipping label format tbd www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 28 11.2. carton package carton label: 80mm * 40mm 97.13bxx.xxx b133ew03 vx www..net
au optronics corporation b133ew03 v0 product specification document version 0.1 29 11.3 shipping package of palletizing bottom cardboard top cardboard stretch film corner angle wooden pallet pet band label www..net

▲Up To Search▲

Price & Availability of B133EW03-V0

	To Download B133EW03-V0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .